By visiting this site, you accept the use of cookies. More about our cookie policy.

GOST 31290-2005

STATE 12339-2016 GOST P 55433-2013 GOST P 55432-2013 GOST 4960-2009 GOST 9722-97 GOST 5494-95 GOST 19106-73 GOST 9453-75 GOST 20559-75 GOST 14086-68 GOST 9723-73 GOST 21125-75 GOST 5426-76 GOST 22025-76 GOST 13834-77 GOST 13833-77 GOST 9721-79 GOST 10285-81 GOST 12342-81 GOST 26719-85 GOST 13084-88 GOST 10096-76 GOST 2330-76 GOST 12343-79 GOST 4411-79 GOST 12338-81 GOST 26252-84 GOST 10284-84 GOST 26802-86 GOST 9849-86 GOST 3882-74 GOST 880-75 GOST 11378-75 GOST 4960-75 GOST 12601-76 GOST 12339-79 GOST 31290-2005 GOST 26630-85 GOST 26530-85 GOST 29278-92 GOST 25405-90 GOST 19046-80 GOST 25406-90 GOST 19078-80 GOST 24257-80 GOST 19065-80 GOST 24247-80 GOST 25412-90 GOST 25396-90 GOST 25400-90 GOST 25425-90 GOST 25410-82 GOST 25420-90 GOST 19074-80 GOST 19083-80 GOST 19048-80 GOST 25414-90 GOST 19062-80 GOST 25415-90 GOST 24253-80 GOST 24251-80 GOST 24249-80 GOST 24254-80 GOST 27302-87 GOST 25393-90 GOST 19067-80 GOST 25411-90 GOST 19068-80 GOST 25397-90 GOST 19059-80 GOST 19049-80 GOST 25398-90 GOST 19075-80 GOST 19061-80 GOST 20312-90 GOST 19051-80 GOST 25402-90 GOST 24252-80 GOST 25417-82 GOST 19043-80 GOST 20771-82 GOST 19081-80 GOST 19086-80 GOST 19056-80 GOST 19047-80 GOST 25421-90 GOST 25413-82 GOST 25418-82 GOST 27301-87 GOST 4872-75 GOST 19084-80 GOST 24255-80 GOST 19050-80 GOST 25401-90 GOST 19052-80 GOST 25426-90 GOST 25423-90 GOST 25399-90 GOST 19073-80 GOST 19057-80 GOST 2209-90 GOST 25403-82 GOST 19044-80 GOST 25408-90 GOST 25395-90 GOST 25409-90 GOST 25407-90 GOST 19071-80 GOST 28378-89 GOST 25419-90 GOST 19045-80 GOST 25003-81 GOST 25394-90 GOST 19077-80 GOST 19072-80 GOST 19080-80 GOST 17163-90 GOST 24250-80 GOST 25424-90 GOST 19063-80 GOST 19070-80 GOST 19076-80 GOST 24256-80 GOST 25422-90 GOST 25404-90 GOST 19064-80 GOST 24248-80 GOST 19069-80 GOST 19079-80 GOST 25416-90 GOST 19053-80 GOST 19042-80 GOST 19085-80

GOST 31290−2005 Platinum affilirovannaja. Specifications (with Change No. 1)


GOST 31290−2005

Group W51


INTERSTATE STANDARD

PLATINUM AFFILIROVANNAJA

Specifications

Refined platinum. Specifications


ISS 77.120
GST 17 5121
17 9431

Date of introduction 2008−01−01



Preface


Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−92 «interstate standardization system. Basic provisions» and GOST 1.2−97 «interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. The procedure of development, adoption, application, renewal and cancellation"

Data on standard

1 DEVELOPED by the Interstate technical Committee for standardization MTK 102 «Platinum metals"

2 as AMENDED by the Federal Agency for technical regulation and Metrology

3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol No. 27 of 22 June 2005)

The adoption voted:

     
Short name of the country on MK (ISO 3166) 004−97
Country code
by MK (ISO 3166) 004−97
Abbreviated name of the national authority for standardization
Azerbaijan
AZ
The Agency «Azstandart"
Armenia
AM
Armastajad
The Republic Of Belarus
BY
Gosstandart Of Belarus
Kazakhstan
KZ
Gosstandart Of The Republic Of Kazakhstan
Kyrgyzstan
KG
Kyrgyzstandard
Moldova
MD
Moldova-Standard
Russian Federation
EN
Federal Agency on technical regulation and Metrology
Tajikistan
TJ
Tajikstandart
Turkmenistan TM The MDCSU «Turkmenstandartlary"
Uzbekistan
UZ
The Agency «Uzstandard"
Ukraine
UA
The state Committee of Ukraine on technical regulation

4 this standard takes into account performance and the standard requirements of ASTM B 561−94 «Standard / specification for platinum» (ASTM 561−94) in terms of chemical composition

5 by Order of the Federal Agency for technical regulation and Metrology dated November 29, 2006 N 283-St inter-state standard GOST 31290−2005 introduced as a national standard of the Russian Federation from January 1, 2008

6 INSTEAD, GOST 12341−81, GOST 14837−79


Information about introduction in action (termination) of this standard is published in the index «National standards».

Information about the amendments to this standard is published in the index «National standards», and the text changes — in the information sign «National standards». In case of revision or cancellation of this standard the appropriate information will be published in the information index «National standards»



The Change N 1, approved and promulgated by the Order of Rosstandart on 12.10.2015 N 1538-St c 01.04.2016

Change No. 1 made by the manufacturer of the database in the text IUS N 1, 2016

1 Scope


This standard applies to affilirovannuju platinum bullion and powder intended for the production of alloys, semi-finished products, chemical compounds of platinum and other purposes.

The standard specifies the requirements for platinum / designed for country needs and export.

2 Normative references


The present standard features references to the following standards:

GOST OIML R 76−1-2011 State system for ensuring the uniformity of measurements. Scales non-automatic actions. Part 1. Metrological and technical requirements. Test

GOST 6613−86 Grids wire woven with square cells. Specifications

GOST 12226−80 Platinum. Methods of analysis*
________________
* On the territory of the Russian Federation there are GOST R 52518−2006 «Platinum. Method for determination of loss on heating», GOST R 52519−2006 «Platinum. Method of atomic-emission analysis with inductively coupled plasma», GOST R 52520−2006 «Platinum. Methods of atomic-emission analysis with arc excitation spectrum», GOST R 52521−2006 «Platinum. Method of atomic-emission analysis with spark excitation spectrum.

GOST 14192−96 Marking of cargo

GOST 17527−2003 Packaging. Terms and definitions

Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.


(Changed edition, Rev. N 1).

2A Terms and definitions


This standard applies the terminology according to GOST 17527, as well as the following terms with respective definitions:

2A.1 document about quality: the Passport, the certificate.

Section 2A (Introduced later, Rev. N 1).

3 Classification, basic parameters and dimensions

3.1 depending on the chemical composition of the platinum is manufactured in the following grades:

PLA-00, PLA-0, PLA-1, PLA-2 — affilirovannaja platinum bullion;

Plap-00, Plap-0, Plap-1, Plap-2 — affilirovannaja platinum powder.

Examples of symbols:

Platinum affilirovannaja brand PLA 00 in the bars:

PLA-00 GOST 31290−2005


Platinum affilirovannaja brand Plap-00 powder:

Plap-00 GOST 31290−2005

3.2 Ingot of platinum needs to be rectangular shape with a length of (100±3) mm and a width of (65±2) mm. the height of the ingot is not regulated.

3.3 the Weight of the ingot shall be not more than 5.5 kg.

3.4 By agreement between manufacturer and customer can be manufactured of platinum in ingots of other shapes, sizes and mass.

3.5 the particle size of the powder of platinum should not exceed 1.6 mm. presence of powder particles larger than 1.6 mm in the amount not exceeding 2% of the batch weight.

4 Technical requirements

4.1 the Characteristics (properties)

4.1.1 affilirovannaja Platinum (more platinum) must comply with the requirements of this standard and be manufactured according to the technical documentation, duly approved.

4.1.2 Chemical composition of platinum bullion and powder should conform to the standards specified in table 1.


Table 1 — Chemical composition of platinum

           
Element*
Mass fraction, %, brands
  PLA-00, Plap-00 PLA-0
Plap-0 PLA-1,
Plap-1
PLA-2, Plap-2
Platinum, minimum (by difference)
99,99 99,98 99,98
99,95
99,90
Impurity, not more than:
0,01
0,02
0,02
0,05
0,10
palladium
0,005
-
-
0,020
-
rhodium
0,005
-
-
0,030
-
iridium
0,005
-
-
0,015
-
ruthenium
0,002
-
-
0,010
-
the amount of platinum group metals
-
0,015
0,015
-
0,050
gold
0,002
0,002
0,002
0,005
0,005
lead
0,001
0,002
0,002
0,005
0,005
iron
0,003
0,003
0,003
0,010
0,010
silicon
0,002
0,002
0,002
0,005
0,005
tin
0,001
0,001
0,001
0,005
0,005
aluminium
0,002
0,002
0,002
0,005
0,005
antimony
0,001
0,001
0,001
0,005
0,005
silver
0,003
0,005
0,005
0,005
-
magnesium
0,002
0,002
0,005
0,005
-
zinc
0,002
0,002
0,005
0,003
-
copper
0,002
0,002
0,005
0,005
-
Nickel
0,001
0,001
0,005
0,003
-
manganese
0,001
0,005
0,005
0,005
-
chrome
0,001
0,005
0,005
0,005
-
arsenic
0,002
0,005
0,005
0,005
-
bismuth
0,002
0,005
0,005
0,005
-
tellurium
0,004
0,005
0,005
0,005
-
calcium
0,003
0,005
0,005
0,005
-
cadmium
0,005
0,005
0,005
0,005
-
molybdenum
0,004
0,010
0,010
0,010
-
* By agreement with the consumer allowed the expansion of the number of detectable elements and determining their maximum permissible mass fraction, and determination of loss on ignition to a platinum powder according to methods of the manufacturer.

4.1.3 the surface of the ingots must be free of burrs, burrs, grease and oil stains, and other extraneous non-metallic inclusions.

Allowed a sweep or zachekanka separate superficial damage on the sides of the ingot with no markings. The number of stripped or zaccarini should be no more than five.

The depth of the denuded and zaccarini places on the surface of ingots shall not exceed 1 mm. Traces of machining rejection characteristics are not.

(Changed edition, Rev. N 1).

4.1.4 platinum Powder should not contain extraneous mechanical inclusions.

4.1.5 Platinum is fire and explosion proof.

4.2 Marking

4.2.1 the front surface of each ingot of platinum labeling, consisting of six prints:

— trademark of the manufacturer;

— numbers (code) of the ingot;

— the symbols of the state of manufacture;

symbol Pt;

— mass fraction of platinum, %;

weight of ingot, g or g.

Apply other stamps (year of issue, the logo of the enterprise) in consultation with the consumer.

Prints on the bars needs to be clear lines of the print must not have gaps must not be double.

(Changed edition, Rev. N 1).

4.2.2 the Order of marking of platinum bullion set by the national regulatory document States the manufacturer, in the absence of the manufacturer in agreement with the consumer.

4.2.2 Affilirovannuju and platinum powder is Packed in consumer packaging — cans or ampoules, ensure the safety of the powder weighing and storage.

(Added, Rev. N 1).

4.2.3 each jar of powder gets a label containing:

— the name of the metal and its brand;

— the batch number;

— the number in the party;

— mass fraction of platinum, %;

— weight gross, net and tare, g;

room specifications;

— the year of issue;

— the designation of this standard.

(Changed edition, Rev. N 1).

4.2.4 On each vial label that contains:

— the name of the metal and its brand;

— the batch number;

— the net mass, g;

— mass fraction of platinum, %;

— the year of issue;

— the designation of this standard.

4.2.5 (Deleted, Rev. N 1).

4.3 Packaging

4.3.1 platinum Bullion and consumer packaging with the platinum in the powder are Packed in shipping containers (GOST 17527). Types of containers, packaging and packing materials must ensure the protection of ingots and consumer packaging with the powder from damage during transportation and storage.

4.3.2 each shipping container glued or fixed otherwise the label (tag) indicating the number of places, room specifications, as well as other details required for delivery.

The shipment of the powder of platinum in sealed shipping containers additionally mark according to GOST 14192 with the indication of manipulation sign «Fragile. Caution."

4.3.3 Each shipping container sealed or sealed with a seal or stamp of the manufacturer.

4.3.4 Each party platinum is accompanied by a document about quality that contains:

— trademark and name of the manufacturer;

— the name of the metal and its brand;

— the batch number;

— mass fraction of platinum, %;

— mass fraction of each determined by the impurity, %;

room specifications;

— the year of issue;

— stamp of quality control;

— the designation of this standard.

4.3.5 Each supply of platinum is accompanied by the specification. In specifications should be specified:

— trademark and name of the manufacturer;

room specifications;

— the name of the metal and its grade;

— the batch number;

— the year of issue;

— the numbers of places;

rooms of bars. (consumer packaging);

the mass of each ingot (net of each unit of consumer package), g;

— mass fraction of platinum, %;

is the mass of pure platinum, g;

— mass fraction of each determined by the impurity, %;

— the total weight of the batch, g;

— the designation of this standard.

4.3.6 Document the quality and specification is protected by plastic film, put in one of the packing stations. Place on packaging labeling «Document here». Allowed to send to the consumer the documents separately.

4.3 (Revised edition, Edit. N 1).

5 acceptance Rules

5.1 Platinum to impose the acceptance of the parties.

Batch of platinum bars must consist of one of the metal bottoms. Number of bars in the party is not standardized.

Batch of platinum powder must consist of metal produced in one technological cycle.

The weight of the batch of platinum should be no more than 350 kg.

5.2, 5.3 (Deleted, Rev. N 1).

5.4 To check the chemical composition from each batch sampled (for platinum in ingots — 6.3, to platinum powder — 6.4).

5.5 Control of surface quality and the presence of foreign inclusions, as well as weight and dimensions of the ingots are subjected to every ingot.

5.6 quality control packaging, labelling and the validity of accompanying documentation is subject to each batch of platinum, each ingot, each Bank, each ampoule.

5.7 If there is disagreement in the assessment of chemical composition the manufacturer and the customer at least one of the indicators, analyze a control sample that is stored with the manufacturer.

6 Methods to control

6.1 controlling the surface quality of ingots of platinum is carried out visually without the use of magnifying devices.

Size control is carried out by means of measurements, providing the required accuracy.

The weight of ingots, powder in jars, ampoules is carried out by weighing on scales conforming to the requirements of GOST OIML R 76−1. Allowed to use other means of mass measurement, ensuring accuracy of weighing in accordance with table 2.


Table 2

In grams

   
Weight
Error
Up to 200 cyl.
±0,0075
SV. 200 to 1000 incl.
±0,01
SV. 1000
±0,1


(Changed edition, Rev. N 1).

6.2 particle size distribution of powder of platinum guarantee technology.

The presence of mechanical impurities is determined by the combined sample visually.

6.3 To check the chemical composition of the platinum sample taken from the melt with obtaining a trial ingots or rods for spectral analysis or another method of selection according to the method of the manufacturer, do not reduce the representativeness of the sample.

The surface of the test bars and the bars need to be flat, and processed by cutting or grinding.

Allowed to acquire a sample by removing shavings no larger than 1 mm from each ingot of the party with one pre-stripped plane, the mass of the joint sample shall be not less than 150 g, weight of prepared sample not less than 120 g. the Minimum sample mass for a party of one or two bars — 60 g.

Determination of the chemical composition of platinum bullion the customer, if necessary, can be performed on the samples taken from any two bars of the party by drilling in the opposite corners and sides of the ingot.

(Changed edition, Rev. N 1).

6.4 For the determination of chemical composition and particle size of platinum powder sampled. For this batch of powder was stirred six times on the ring and cone and reduce kvantovanie with stirring at every stage to the mass of the joint sample at least 5% of the batch weight. The combined sample is sieved through a sieve with cell size of 1.6 mm according to GOST 6613, averaged and reduced to the weight of the prepared sample (not less than 200 g).

Allowed the selection of ready samples by the method of restraint of the jet of powder of platinum when it is unloaded from the mixer after the mechanical averaging.

6.5 analysis of the chemical composition of platinum is carried out according to GOST 12226* and other methods to ensure accuracy is not below the predetermined specified standard.
________________
* On the territory of the Russian Federation are 52518 GOST R, GOST R 52519, 52520 GOST R, GOST R 52521.

The manufacturer guarantees that the content of platinum in bullions and powder form in accordance with the requirements of 4.1.2.

(Changed edition, Rev. N 1).

6.6 storage Time control sample is 30 calendar days from the date of shipment, unless otherwise provided by the terms of the contract.

(Changed edition, Rev. N 1).

7 Transportation and storage

7.1 Platinum bullion and powder transporterowych and stored in accordance with the requirements of the Federal financial authorities of the state of the manufacturer.

7.1.1 Transportation of platinum is carried out in a Packed form and in accordance with the regulatory requirements of the organization providing the transportation.

7.1.2 Storage of platinum from the manufacturer and the consumer is carried out in Packed in conditions that ensure the safety of goods from damage and spoilage.

Shelf life of platinum in the manufacturer’s packaging is not limited.