GOST R 55395-2013

• gost-r-55395-2013.pdf (662.23 KiB)
  ГОСТ Р 55395-2013

GOST R 55395−2013 extruded strips of curved cross-section of aluminum alloy. Assortment

GOST R 55395−2013

Group В52

NATIONAL STANDARD OF THE RUSSIAN FEDERATION

EXTRUDED STRIPS OF CURVED CROSS-SECTION OF ALUMINIUM ALLOYS

Assortment

Extruded strip-like section aluminium alloy shapes with arched cut-outs. Dimensions

OKS 77.150.10
GST 18 1141

Date of introduction 2014−06−01

Preface

1 DEVELOPED by the Technical Committee for standardization TC 297 «Materials and semi-finished products from light and special alloys» (JSC «all-Russia Institute of light alloys»)

2 SUBMITTED by the Technical Committee for standardization TC 297 «Materials and semi-finished products from light and special alloys"

3 APPROVED AND put INTO EFFECT by the Federal Agency for technical regulation and Metrology dated 12 March 2013 N 11-St

4 INTRODUCED FOR THE FIRST TIME

Application rules of this standard are established in GOST R 1.0−2012 (section 8). Information about the changes to this standard is published in the annual (as of January 1 of the current year) reference index «National standards» and the official text changes and amendments — in monthly information index «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in the upcoming issue of the monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet (gost.ru)

1 Scope

This standard establishes the assortment of extruded profile strips of curved sections of aluminum alloys manufactured by hot pressing and intended for pad clamps.

2 Normative references

In this standard, reference the following standard:

GOST 4784−97 Aluminum and aluminum deformable alloys. Brand

Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If replaced with a reference standard, which was given an undated reference, then it is recommended to use the current version of this standard, taking into account all enabled in this version modifications. If replaced with a reference standard, which is given a dated reference, it is recommended to use the version of this standard referred to above by year of approval (acceptance). If after approval of this standard in the reference standard, which is given a dated reference, a change affecting a provision to which reference, the provision is recommended to be applied without taking into account this change. If the reference standard is cancelled without replacement, the position in which reference is made to him, recommended to be used in part not affecting this link.

3 Main parameters and dimensions

3.1 the shape of the profiles and their dimensions shall conform to the values given in figures 1−12 and tables 1−12.

Figure 1−12 the shape of the profiles and their sizes

Figure 1

Table 1

Profile number	Dimensions, mm									The cross-sectional area, cm	Theoretical weight 1 m, kg
Six hundred one thousand seven hundred eighty	6,0	23,0	16,0	1,0	7,0	8,0	1,0	1,0	1,0	Of 1.09	0,31
601761	6,0	24,0	17,0	1,0	7,0	8,2	1,5	1,5	-	1,15	0,33
601762	7,5	25,0	17,0	0,5	8,0	9,0	1,0	1,0	-	1,46	0,42
601782	7,5	25,0	17,0	0,5	8,0	10,0	1,0	1,0	1,0	1,38	0,39
601763	8,0	26,0	17,0	1,0	9,0	10,2	1,0	1,0	-	1,59	0,45
601779	8,5	27,0	18,0	0,5	9,0	12,0	1,0	1,0	1,0	1,59	0,45
601764	8,5	28,5	19,0	1,0	9,5	13,0	1,0	1,0	-	1,70	0,48
601765	9,0	25,0	18,0	0,2	8,0	11,4	2,0	2,0	1,0	1,59	0,45
601766	9,0	27,0	18,0	0,2	10,0	12,0	2,0	2,0	1,0	1,64	0,47
601767	9,0	28,0	19,0	0,2	9,0	13,0	2,0	2,0	1,0	1,68	0,48
601768	9,5	29,0	19,0	0,2	10,0	13,0	2,0	2,0	1,0	1,96	0,56
601784	9,5	29,0	19,0	0,5	10,0	14,0	1,0	1,0	1,0	1,83	0,52
601769	9,7	33,0	23,0	0,2	10,0	14,0	1,0	1,0	0,5	2,20	0,63
601770	10,5	34,0	23,0	0,5	11,0	16,0	1,0	1,0	0,5	2,39	0,68
601771	11,0	31,0	21,0	0,2	12,0	16,0	2,0	2,0	1,0	2,10	0,60
601772	11,5	32,5	20,5	0,5	12,0	18,0	1,0	1,0	0,5	2,02	0,58
601773	11,5	37,0	24,5	1,0	12,5	18,2	1,5	1,5	-	2,79	0,80
601774	12,0	34,5	22,0	0,5	12,5	19,0	2,0	2,0	1,0	2,48	0,71
601775	12,5	37,2	24,2	0,5	13,0	20,0	1,0	1,0	1,0	Of 2.78	0,79
601776	13,0	39,0	25,0	1,0	14,0	20,2	1,0	1,0	-	3,23	0,92
601777	14,5	43,0	27,0	1,5	16,0	26,0	-	-	-	The 3.42	0,97
601778	15,0	46,0	30,0	1,0	16,0	23,2	1,5	1,5	-	4,44	1,27
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile equal to 6.0 mm; — 0.8 mm — thickness of the shelf profile is more than 6.0 to 10.0 mm; — 1.0 mm — thickness of shelf profiles is more than 10.0 to 15 mm.

Figure 2

Table 2

Profile number	Dimensions, mm											The cross-sectional area, cm	Theoretical weight 1 m, kg
Six hundred one thousand nine hundred thirty	3,5	30,5	21,5	1,0	9,0	10,2	2,0	-	1,5	1,5	-	1,16	0,33
601931	3,5	32,5	23,0	1,0	9,0	12,2	2,0	-	1,5	1,5	-	1,14	0,32
601932	4,0	31,0	23,0	1,0	8,0	10,0	3,0	-	-	1,5	0,5	1,20	0,34
601933	4,0	35,0	25,0	1,0	10,0	14,0	3,0	-	-	1,5	0,5	1,40	0,40
601934	4,0	37,0	26,0	0,5	11,0	15,0	3,0	1,5	1,5	1,5	-	1,62	0,46
601935	4,0	46,0	30,0	1,0	16,0	23,2	1,5	-	1,5	1,5	-	2,42	0,69
601936	4,0	48,0	31,0	1,0	17,0	27,2	1,5	-	1,5	1,5	-	2,35	0,67
601937	5,0	32,5	22,0	1,0	10,5	14,2	1,5	-	1,5	1,5	-	Of 1.47	0,42
601938	5,0	39,5	28,5	0,5	11,0	16,0	3,0	0,5	1,0	1,0	0,5	1,83	0,52
601939	5,5	34,0	23,0	0,5	11,0	16,0	3,0	0,5	1,0	1,0	0,5	1,67	0,48
601940	5,7	33,0	23,0	0,2	10,0	14,0	2,0	0,5	1,0	1,0	0,5	1.52 m	0,43
601941	6,0	38,0	28,0	1,0	10,0	14,2	1,5	-	1,5	1,5	-	1,80	0,51
601942	6,0	42,0	28,0	0,5	14,0	21,0	3,0	1,5	1,5	1,5	-	2,19	0,62
601943	6,0	49,0	33,5	1,0	15,5	21,4	1,5	-	1,5	1,5	-	3,13	0,89
601944	6,5	37,0	24,5	1,0	12,5	18,2	2,0	-	1,5	1,5	-	Of 1.88	0,54
601945	6,5	43,0	27,0	1,5	16,0	26,0	1,5	-	-	-	-	Of 2.00	0,57
601946	6,5	46,5	30,0	0,5	16,5	27,0	3,0	0,5	1,0	1,0	0,5	2,39	0,68
601947	7,0	39,0	25,0	1,0	14,0	20,2	1,0	-	1,0	1,0	-	2,20	0,63
601948	7,0	52,5	34,0	0,5	18,5	29,0	3,0	1,5	1,5	1,5	-	3,16	0,90
601953	7,5	32,0	21,0	0,5	11,0	16,0	2,5	1,0	1,0	1,0	1,0	1,68	0,48
601949	7,5	36,0	24,0	0,5	12,0	18,0	3,0	0,5	1,0	1,0	0,5	2,11	0,60
601950	7,5	37,2	24,2	0,5	13,0	20,0	2,0	0,5	1,0	1,0	0,5	1,92	0,55
601954	8,5	34,0	22,0	0,5	12,0	18,0	2,5	-	-	-	-	1,90	0,54
601951	8,5	39,0	25,0	0,5	14,0	21,0	-	-	1,0	1,0	-	2,33	0,66
601958	8,5	41,0	26,0	0,5	15,0	24,0	2,5	1,0	1,0	1,0	1,0	2,26	0,64
601952	9,5	32,5	20,5	0,5	12,0	18,0	2,0	0,5	1,0	1,0	0,5	1,86	0,53
601961	9,5	47,0	29,0	0,5	18,0	30,0	2,5	1,0	1,0	1,0	1,0	2,69	0,77
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile from 3.5 to 6.0 mm; — 0.8 mm — thickness of shelf profiles is more than 6.0 to 9.5 mm.

Figure 3

Table 3

Profile number	Dimensions, mm									The cross-sectional area, cm	Theoretical weight 1 m, kg
602185	6,0	30,0	16,0	1,0	7,0	8,0	-	-	-	1,25	0,36
602187	6,5	30,0	16,0	0,5	7,0	6,0	1,5	1,5	1,5	1,60	0,46
602188	6,5	32,0	18,0	0,5	7,0	5,0	1,0	1,0	-	1,72	0,49
602223	6,5	32,0	18,0	0,5	7,0	8,0	1,0	1,0	1,0	1,43	0,41
602190	6,5	33,0	18,0	1,0	7,5	8,2	1,5	1,5	-	1,57	0,45
602191	6,7	34,0	20,0	0,2	7,0	7,0	1,0	1,0	0,5	1,69	0,48
602195	7,5	36,0	20,0	0,5	8,0	9,0	1,0	1,0	-	Of 1.88	0,54
602225	7,5	36,0	20,0	0,5	8,0	10,0	1,0	1,0	1,0	1,76	0,50
602197	8,0	39,0	21,0	1,0	9,0	12,3	1,0	1,0	-	1,85	0,53
602198	8,0	40,0	22,0	1,0	9,0	12,0	1,0	0,5	0,5	Of 2.00	0,57
602204	8,0	44,0	26,0	1,0	9,0	12,3	1,5	1,5	-	2,22	0,63
602228	8,5	40,0	22,0	0,5	9,0	12,0	1,0	1,0	1,0	2,03	0,58
602221	8,5	44,0	26,0	0,5	9,0	12,0	1,0	1,0	1,0	2,40	0,68
602209	9,0	43,0	23,0	1,0	10,0	14,3	1,0	1,0	1,0	2,18	0,62
602210	9,0	44,0	24,0	1,0	10,0	8,0	1,0	1,0	1,5	2,60	0,74
602212	9,5	44,0	24,0	0,5	10,0	14,0	1,0	1,0	-	2,35	0,67
602222	9,5	46,0	26,0	0,5	10,0	14,0	1,0	1,0	1,0	2,50	0,74
602216	10,0	50,0	28,0	1,0	11,0	14,3	1,5	1,5	-	3,16	0,90
602232	10,5	48,0	26,0	0,5	11,0	16,0	1,0	1,0	1,0	Of 2.66	0,76
602233	11,5	52,0	28,0	0,5	12,0	18,0	1,0	1,0	1,0	2,99	0,85
602217	11,5	60,0	35,0	1,0	12,5	18,3	1,5	1,5	-	4,06	1,16
602218	12,0	61,0	35,0	1,0	13,0	18,0	-	-	-	4,41	1,26
602235	12,5	56,0	30,0	0,5	13,0	20,0	1,0	1,0	1,0	3,32	0,95
602236	13,5	60,0	32,0	0,5	14,0	22,0	1,0	1,0	1,0	3,67	1,05
602219	13,5	63,0	35,0	0,5	14,0	21,0	2,0	2,0	1,0	4,40	1,25
602220	14,0	63,0	33,0	1,0	15,0	18,0	1,0	1,0	1,5	The 4.67	Of 1.34
602237	17,5	76,0	40,0	0,5	18,0	30,0	1,0	1,0	1,0	5,13	1,46
602238	19,5	84,0	44,0	0,5	20,0	34,0	1,0	1,0	1,0	5,91	1,68

Figure 4

Table 4

Profile number	Dimensions, mm										The cross-sectional area, cm	Theoretical weight 1 m, kg
Six hundred two thousand one hundred eighty nine	6,5	33,0	18,0	1,0	7,5	8,2	6,2	1,5	1,5	-	1,67	0,48
602192	7,0	32,0	17,0	0,5	7,5	8,0	6,0	1,5	1,5	1,5	1,68	0,48
602193	7,0	33,0	17,0	1,0	8,0	10,0	8,0	-	-	-	1,60	0,46
602194	7,5	35,0	18,0	1,0	8,5	10,2	8,2	1,5	1,5	-	1,83	0,52
602224	7,5	35,0	19,0	0,5	8,0	10,0	8,0	1,0	1,0	1,0	1,78	0,51
602196	8,0	36,0	18,0	1,0	9,0	12,0	8,0	-	-	-	1,90	0,54
602199	8,0	40,0	22,0	1,0	9,0	13,0	12,0	1,0	1,0	1,0	1,87	0,53
Six hundred two thousand two hundred	8,0	40,0	22,0	1,0	9,0	12,3	6,2	1,5	1,5	-	2,29	0,65
602201	8,0	40,0	22,0	1,0	9,0	12,3	8,2	1,5	1,5	-	2,18	0,62
602202	8,0	41,0	23,0	1,0	9,0	12,3	10,2	1,0	1,0	-	2,17	0,62
602203	8,0	44,0	26,0	1,0	9,0	12,3	10,2	1,5	1,5	-	2,39	0,68
602226	8,5	38,0	20,0	0,5	9,0	12,0	8,0	1,0	1,0	1,0	2,15	0,61
602205	8,5	39,0	21,0	0,5	9,0	11,0	9,0	1,0	-	-	2,26	0,64
602206	8,5	39,0	21,0	0,5	9,0	12,0	10,0	1,0	1,0	1,0	2,12	0,60
602207	9,0	41,0	21,0	1,0	10,0	14,3	10,2	1,0	1,0	-	2,31	0,66
602208	9,0	43,0	23,0	1,0	10,0	14,3	13,0	1,0	1,0	-	2,28	0,65
602211	9,0	45,0	25,0	1,0	10,0	14,3	12,3	1,5	1,5	-	2,49	0,71
602229	9,5	42,0	22,0	0,5	10,0	14,0	10,0	1,0	1,0	1,0	2,28	0,65
602230	9,5	43,0	23,0	0,5	10,0	14,0	12,0	1,0	1,0	1,0	2,19	0,62
602213	10,0	43,0	21,0	1,0	11,0	14,3	10,2	1,0	1,0	-	2,85	0,81
602214	10,0	46,0	24,0	1,0	11,0	16,0	12,0	1,0	1,0	-	Of 2.78	0,79
602215	10,0	49,0	27,0	1,0	11,0	16,3	14,3	1,0	1,0	-	2,90	0,83
602231	10,5	46,0	24,0	0,5	11,0	16,0	12,0	1,0	1,0	1,0	2,87	0,82
602242	10,5	49,0	27,0	0,5	11,0	18,0	14,0	-	1,0	-	2,73	0,78
602243	12,0	53,0	29,0	1,0	13,0	18,0	10,0	-	-	-	4,25	1,21
602234	12,5	54,0	28,0	0,5	13,0	20,0	16,0	1,0	1,0	1,0	3,62	1,03

Figure 5

Table 5

Profile number	Dimensions, mm							The cross-sectional area, cm	Theoretical weight 1 m, kg
602262	6,0	22,0	13,0	5,5	5,5	1,75	1,0	0,90	0,26
602250	6,0	24,0	14,0	6,5	6,5	1,75	1,0	0,90	0,26
602251	7,0	28,0	16,0	8,5	8,5	1,75	1,0	1,29	0,37
602252	7,0	26,0	15,0	6,5	8,5	1,75	1,0	1,27	0,36
602263	8,0	28,0	16,0	6,5	10,5	1,75	1,0	1,65	0,47
602264	8,0	30,0	17,0	8,5	10,5	1,75	1,0	1,54	0,44
602265	8,0	32,0	18,0	10,5	10,5	1,75	1,0	Of 1.51	0,43
602272	9,0	30,0	17,0	6,5	12,5	1,75	1,0	1,78	0,51
602266	9,0	32,0	18,0	8,5	12,5	1,75	1,0	1,84	0,52
602273	9,0	34,0	19,0	10,5	12,5	1,75	1,0	Of 1.88	0,54
602267	9,0	36,0	20,0	12,5	12,5	1,75	1,0	Of 1.88	0,54
602268	10,0	36,0	20,0	10,5	14,5	1,75	1,0	2,19	0,62
602269	10,0	38,0	21,0	12,5	14,5	1,75	1,0	2,22	0,63
602274	10,5	37,0	20,5	10,5	15,5	1,75	1,0	2,37	0,68
602275	11,0	38,0	21,0	10,5	16,5	1,75	1,0	Of 2.53	0,72
602276	11,0	42,0	23,0	14,5	16,5	1,75	1,0	2,59	0,74
602277	12,0	48,0	26,0	18,5	18,5	1,75	1,0	2,94	0,84
602270	13,0	44,0	24,0	12,5	20,5	1,75	1,0	3,32	0,95
602271	14,0	46,0	25,0	12,5	22,5	1,75	1,0	3,70	1,05
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile equal to 6.0 mm; — 0.8 mm — thickness of the shelf profile is more than 6.0 to 10.0 mm; — 1.0 mm — thickness of shelf profiles is more than 10.0 to 14.0 mm.

Figure 6

Table 6

Profile number	Dimensions, mm												The cross-sectional area, cm	Theoretical weight 1 m, kg
Six hundred two thousand three hundred eighty	9,0	42,0	24,0	7,0	1,0	10,0	8,0	8,0	4,0	5,0	-	-	2,85	0,81
602406	9,5	40,0	23,0	6,5	0,5	10,0	7,0	14,0	8,0	2,5	1,0	1,0	1,81	0,52
602381	9,5	42,5	24,0	7,0	1,0	10,5	8,0	12,2	10,2	1,5	1,5	-	Of 2.06	0,59
602382	9,5	43,5	25,0	7,0	1,0	10,5	8,0	14,2	8,2	1,5	1,5	-	Of 2.23	0,64
602383	10,0	43,0	23,0	8,0	1,0	11,0	9,0	15,2	6,2	1,5	1,5	-	2,41	0,69
602408	10,0	43,0	24,0	7,0	1,0	11,0	8,0	16,0	10,0	2,5	1,0	-	1,98	0,56
602384	10,0	45,0	25,0	8,0	1,0	11,0	9,0	14,2	10,2	2,0	1,5	-	2,40	0,68
602407	10,5	43,0	24,0	7,5	0,5	11,0	8,0	16,0	10,0	2,5	1,0	1,0	2,03	0,58
602409	11,0	45,0	25,0	7,0	1,0	12,0	8,0	18,0	10,0	2,5	1,0	-	Of 2.05	0,58
602385	11,0	47,0	27,0	7,0	1,0	12,0	8,0	12,0	6,0	3,0	-	-	Is 3.08	0,88
602386	11,0	54,0	33,0	8,0	1,0	12,0	9,0	12,0	8,0	3,0	1,5	1,5	3,70	1,05
602387	11,0	50,5	29,0	8,5	1,0	12,0	9,5	18,0	13,0	3,0	1,0	-	2,64	0,75
602388	11,5	45,0	25,0	6,5	1,0	12,5	7,5	16,2	8,2	1,5	1,5	-	2,50	0,71
602389	11,5	48,5	26,0	9,0	1,0	12,5	10,0	18,2	12,2	1,5	1,5	-	2,70	0,77
602390	12,0	50,0	27,0	9,0	1,0	13,0	10,0	20,0	14,0	3,0	1,0	-	2,50	0,71
602391	13,0	56,0	30,0	11,0	1,0	14,0	12,0	23,0	16,2	3,0	-	-	Of 3.00	0,86
602392	13,5	51,5	27,0	9,0	1,0	14,5	10,0	21,4	12,2	3,0	1,0	-	Of 2.84	0,81
602393	13,5	51,5	27,0	9,0	1,0	14,5	10,0	22,2	12,2	1,5	1,5	-	Of 2.78	0,79
602414	13,5	54,0	29,0	10,5	0,5	14,0	11,0	22,0	16,0	2,5	1,0	1,0	2,96	0,84
602410	14,0	56,0	30,0	10,0	1,0	15,0	11,0	24,0	16,0	2,5	1,0	-	2,86	0,82
602394	14,0	56,0	31,0	9,0	1,0	15,0	10,0	18,0	8,0	5,0	1,5	1,5	4,30	Of 1.23
602395	14,0	57,0	33,0	8,0	1,0	15,0	9,0	18,0	8,0	3,0	1,5	1,5	Of 4.00	1,14
602396	14,5	58,0	35,0	7,5	0,5	15,0	8,0	11,0	4,0	5,0	1,5	1,5	5,09	1,45
602397	15,5	59,5	33,0	9,0	1,0	16,5	10,0	22,0	8,0	3,0	-	-	4,44	1,27
602398	15,5	58,5	34,0	7,0	1,0	16,5	8,0	21,0	4,0	3,0	1,5	1,5	Of 3.98	1,13
602399	15,5	58,5	34,0	7,0	1,0	16,5	8,0	22,0	6,0	3,0	-	-	Of 2.78	0,79
602400	15,5	62,5	34,0	11,0	1,0	16,5	12,0	22,0	12,0	3,0	-	-	4,94	1,41
602401	17,0	60,0	32,0	9,0	1,0	18,0	10,0	29,2	10,2	1,5	1,0	-	3,43	0,98
602435	17,5	71.0 per	38,0	14,5	0,5	18,0	15,0	30,0	24,0	2,5	1,0	1,0	The 4.67	1,33
602402	19,0	67,0	37,0	9,0	1,0	20,0	10,0	28,0	8,0	3,0	-	-	5,24	1,49
602403	19,0	72,0	40,0	11,0	1,0	20,0	12,0	28,0	12,0	3,0	-	-	Of 6.03	1,72
602404	21,5	73,0	40,0	8,5	1,5	23,0	10,0	40,0	14,0	3,0	1,0	1,0	3,50	Of 1.00
602412	26,0	86,5	47,0	10,5	1,5	27,5	12,0	44,0	17,0	1,0	-	-	6,16	1,76
602405	26,0	90,0	52,0	10,0	1,0	27,0	11,0	42,0	9,0	5,0	-	-	7,29	Of 2.08

Figure 7

Table 7

Profile number	Dimensions, mm									The cross-sectional area, cm	Theoretical weight 1 m, kg
602701	6,0	30,0	8,0	13,0	4,5	3,0	5,5	5,5	5,5	Of 1.34	0,38
602713	6,0	31,0	8,5	13,0	5,0	3,0	6,5	5,5	5,5	1,36	0,39
602702	6,0	33,0	9,0	14,0	5,0	5,0	6,5	6,5	6,5	1,35	0,38
602703	7,0	35,0	10,0	15,0	5,0	5,0	6,5	8,5	6,5	1,66	0,47
602704	7,0	35,0	9,0	15,0	5,0	5,0	6,5	6,5	8,5	1,66	0,47
Six hundred two thousand seven hundred five	7,0	37,0	10,0	16,0	5,0	5,0	6,5	8,5	8,5	1,69	0,48
602706	7,0	39,0	11,0	16,0	6,0	5,0	8,5	8,5	8,5	1,99	0,57
602707	8,0	37,0	9,0	16,0	5,0	5,0	6,5	6,5	10,5	2,14	0,61
602708	9,0	39,0	9,0	17,0	5,0	5,0	6,5	6,5	12,5	2,39	0,68
602709	9,0	45,0	12,0	20,0	5,0	5,0	6,5	12,5	12,5	2,45	0,70
602710	9,0	47,0	13,0	20,0	6,0	5,0	8,5	12,5	12,5	2,55	0,73
602711	11,0	62,0	21,0	24,0	7,0	5,0	10,5	16,5	16,5	Of 4.03	1,15
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile equal to 6.0 mm; — 0.8 mm — thickness of shelf profiles is more than 6.0 to 9.0 mm; — 1.0 mm — thickness of the shelf profile is 11.0 mm.

Figure 8

Table 8

Profile number	Dimensions, mm									The cross-sectional area, cm	Theoretical weight 1 m, kg
602790	5,0	33,0	14,0	21,0	0,5	6,0	6,0	6,0	6,0	1,22	0,35
602791	6,0	50,0	18,0	36,0	1,0	7,0	8,0	8,0	8,0	2,38	0,68
602792	6,5	38,0	9,0	24,0	0,5	7,0	6,0	6,0	10,0	1,57	0,45
602793	7,5	49,0	17,0	33,0	0,5	8,0	10,0	6,0	8,0	2,60	0,74
602794	8,5	52,0	21,0	34,0	0,5	9,0	12,0	8,2	11,4	2,70	0,77
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile from 5.0 to 6.0 mm; — 0.8 mm — thickness of shelf profile from 6.5 to 8.5 mm.

Figure 9

Table 9

Profile number	Dimensions, mm										The cross-sectional area, cm	Theoretical weight 1 m, kg
602901	6,0	47,0	14,5	9,0	9,0	0,6	-	6,8	6,8	6,8	2,40	0,68
602902	6,5	60,0	16,0	14,0	14,0	1,5	3,0	10,0	10,0	10,0	3,20	0,91
602903	7,5	66,0	17,0	16,0	16,0	1,5	3,0	14,0	14,0	14,0	3,20	0,91
602904	8,0	51,0	14,5	10,0	11,0	0,6	-	6,8	8,8	8,8	3,40	0,97
602905	8,0	53,0	15,5	11,0	11,0	0,6	-	8,8	8,8	8,8	3,50	Of 1.00
602906	8,0	55,0	15,5	11,0	12,0	0,6	-	8,8	8,8	10,8	3,60	1,03
602907	8,5	72,0	18,0	18,0	18,0	1,5	3,0	16,0	16,0	16,0	3,80	Of 1.08
602908	10,0	66,0	18,0	18,0	15,0	1,0	-	8,0	8,0	5,0	4.62 a	1,32
602909	13,0	85,0	19,5	21,0	23,0	0,6	-	16,8	20,8	20,8	7,00	Of 2.00

Figure 10

Table 10

The number of Pro- Phil	Dimensions, mm												The cross-sectional area, cm	Theoretical of Korea weight 1 m, kg
Six hundred two thousand eight hundred sixty five	6,0	56,0	14,5	9,0	9,0	9,0	0,6	6,8	6,8	6,8	6,8	-	2,80	0,80
602879	6,0	58,0	14,0	10,0	10,0	10,0	1,5	8,0	8,0	8,0	8,0	1,0	2,95	0,84
602880	7,0	62,0	14,0	10,0	11,0	12,0	1,5	8,0	8,0	10,0	10,0	1,0	3,58	1,02
602881	7,0	66,0	15,0	12,0	12,0	12,0	1,5	10,0	10,0	10,0	10,0	1,0	3,64	Of 1.04
602866	8,0	62,0	14,5	10,0	11,0	10,0	0,6	6,8	8,8	8,8	6,8	-	4,17	1,19
602867	8,0	64,0	15,5	11,0	11,0	11,0	0,6	8,8	8,8	8,8	8,8	-	3,56	1,01
602868	8,0	89,0	14,5	19,0	19,0	19,0	0,6	6,8	6,8	6,8	6,8	-	6,75	1,92
602882	9,0	82,0	17,0	16,0	16,0	16,0	1,5	14,0	14,0	14,0	14,0	1,0	5,10	1,45
602869	13,0	106,0	19,5	21,0	23,0	21,0	0,6	16,8	20,8	20,8	16,8	-	8,61	2,45

Figure 11

Table 11

Profile number	Dimensions, mm										The cross-sectional area, cm	Theoretical weight 1 m, kg
Six hundred two thousand seven hundred fifty five	6,0	49,0	12,5	8,0	8,0	8,0	5,5	5,5	5,5	5,5	2,35	0,67
602756	6,0	53,0	13,0	9,0	9,0	9,0	6,5	6,5	6,5	6,5	2,36	0,67
602796	7,0	55,0	13,0	9,0	9,0	10,0	6,5	6,5	6,5	8,5	2,95	0,84
602797	7,0	55,0	14,0	9,5	8,0	9,5	8,5	5,5	5,5	8,5	Of 2.91	0,83
602802	7,0	55,0	12,5	8,0	9,5	11,0	5,5	5,5	8,5	8,5	2,93	0,84
602798	7,0	57,0	14,0	10,0	10,0	10,0	8,5	6,5	8,5	6,5	2,97	0,85
602799	7,0	57,0	14,0	11,0	10,0	9,0	8,5	8,5	6,5	6,5	2,97	0,85
602801	7,0	57,0	13,0	10,0	11,0	10,0	6,5	8,5	8,5	6,5	2,97	0,85
602800	7,0	59,0	13,0	10,0	11,0	11,0	6,5	8,5	8,5	8,5	2,99	0,85
602753	8,0	57,0	13,0	9,0	9,0	11,0	6,5	6,5	6,5	10,5	3,54	1,01
602804	9,0	77,0	16,0	15,0	15,0	15,0	12,5	12,5	12,5	12,5	4,36	1,24
602803	10,0	75,0	15,0	15,0	16,0	14,0	10,5	14,5	12,5	10,5	5,08	1,45
Note — the Radius of the rounded corners, not shown in the figure should be no more than: — 0.6 mm — thickness of shelf profile equal to 6.0 mm; — 0.8 mm — thickness of shelf profile from 7.0 to 10.0 mm.

Figure 12

Table 12

The number of Pro- Phil	Dimensions, mm														PLO the area of the cross section- tion, see	Theoretical of Korea weight 1 m, kg
Six hundred two thousand eight hundred thirty two	7,0	73,0	13,0	9,0	9,0	9,0	9,0	10,0	6,5	6,5	6,5	6,5	6,5	8,5	3,83	Of 1.09
602833	7,0	75,0	13,0	10,0	11,0	10,0	9,0	9,0	6,5	8,5	8,5	6,5	6,5	6,5	3,85	1,10
602834	7,0	75,0	13,0	9,0	10,0	10,0	10,0	10,0	6,5	6,5	8,5	6,5	8,5	6,5	3,85	1,10
602835	7,0	75,0	14,0	10,0	9,0	10,0	10,0	9,0	8,5	6,5	6,5	8,5	6,5	6,5	3,85	1,10
602836	7,0	75,0	14,0	10,0	10,0	10,0	9,0	9,0	8,5	6,5	8,5	6,5	6,5	6,5	3,85	1,10
602837	7,0	79,0	14,0	11,0	11,0	11,0	10,0	9,0	8,5	8,5	8,5	8,5	6,5	6,5	3,89	1,11
Note — the Radius of the rounded corners, not shown in the figure should be no more than 0.8 mm.

3.2 Radii , , , , , , not specified in tables 1−12, must be no more than:

— 0.6 mm — thickness of shelf profile from 3.5 to 6.0 mm;

— 0.8 mm — thickness of the shelf profile is more than 6.0 to 10.0 mm;

A 1.0 mm thickness of the shelf profile in excess of 10.0 to 18.0 mm;

— 1.2 mm — thickness of the shelf profile in excess of 18.0 to 26.0 mm.

3.3 Profiles are made of aluminum alloys of Amg3, AMg6, AB, D1, D16, D16ch, D19, D19ch, AK4−1, AK4−1ch with the chemical composition according to GOST 4784.

3.4 Theoretical weight of 1 m calculated with nominal size at a density of 2.85 kg/DM, which corresponds to the density of the aluminum alloy V95 brand. Conversion factors to calculate the approximate theoretical weight of 1 m of profile of aluminium alloys is given in Appendix A.

3.5 numbers corresponding profiles previously existing designations are given in Appendix B.

Annex a (informative). Conversion factors

Appendix A
(reference)

Table A. 1 — Conversion factors for calculating the approximate theoretical weight of 1 m of aluminium alloy sections of

Grade	Density, kg/DM	The conversion factor
Amg3	Of 2.66	0,933
AMg6	2,64	0,926
AV	2,70	0,947
D1	2,80	0,982
D16	2,77	0,972
D16ch	Of 2.78	0,976
D19	2,76	0,968
D19ch	2,76	0,968
AK4−1	2,80	0,982
AK4−1ch	2,80	0,982

Annex B (reference). Numbers corresponding profiles

Appendix B
(reference)

Table B. 1 — numbers corresponding profiles previously existing symbols

Profile number	Designation of the profile according to the drawings
601761	With 550
601762	With 662
601763	WITH 1327−1, PC 15224
601764	WITH 1327−2, PC 15227
601765	529−3 PP, PC 1663
601766	PP 529−4
601767	PP 529−5, PC 1673
601768	PP 529−1, PC 1473−2
601769	PC 11380−2
601770	PC 11372
601771	529−6 PP, PC 1660
601772	PC 11379−1
601773	With 789
601774	PP 529−2, PC 1473−2
601775	PC 11386−1
601776	WITH 1327−3, PC 15204
601777	PC 12845, 859
601778	With 778
601779	NP 1851−1
601780	NP 1851−2
601782	NP 1851−5
601784	NP 1851−4
601930	With 791−2
601931	With 791−1
601932	PS 991−1
601933	PS 991−2
601934	WITH 689−1, PC 11588
601935	With 793
601936	With 1328−2
601937	With 792
601938	PC 11378
601939	PC 11377
601940	PC 11380−1
601941	With 564
601942	WITH 689−2, PC 11590, PP 737−2
601943	WITH 1328−3, PC 15232
601944	With 794
601945	With 861−2
601946	PC 11376
601947	WITH 1328−1, PC 15203
601948	WITH 689−3, PC 11590, PP 737−3
601949	PC 11374
601950	PC 11386−2, PC 11375
601951	With 663
601952	PC 11379−2
601953	NP 1852−3
601954	NP 1852−4
601958	NP 1852−1
601961	NP 1852−2
602185	PS 713−8, PC 12045−1
602187	PC 0523
602188	From 661
602189	With 561
602190	With 560
602191	PC 13338−1
602192	PC 0532
602193	PS 713−9, PC 12045−2
602194	With 559
602195	With 660
602196	PS 713−10, PC 12045−3
602197	WITH 1329−1, PC 15229
602198	PS 678−1
602199	WITH 1329−2, PC 15226
602200	With 556−1
602201	With 556−2
602202	WITH 1329−3, PC 15220
602203	With 798
602204	WITH 551А
602205	With 664
602206	WITH 491, NP 1843−5, PC 9812−1
602207	WITH 1329−4, PC 15225
602208	WITH 1329−6, PC 15222
602209	WITH 1329−7, PC 15231
602210	PC 9435
602211	With 557
602212	WITH 490, PC 9812−2, NP 1842−5
602213	WITH 1329−5, PC 15223
602214	WITH 1329−8, PC 15230
602215	WITH 1329−9, PC 15214
602216	With 552
602217	With 547
602218	PS 713−6
602219	PP 531−8
602220	PC 9429
602221	PK 17437
602222	PC 17438
602223	PC 19484, 2122−1, NP 1842−2, PC 4525−1
602224	NP 1843−3
602225	PC 19485, 2122−2, 2212, PC 7031, NP 1842−3, PC 4525−2
602226	NP 1843−4
602228	NP 1842−4, PC 19486, 2122−3, PC 4525−3
602229	NP 1843−6
602230	NP 1843−7
602231	PC 19744, 2122−4, NP 1843−8
602232	NP 1842−6
602233	NP 1842−7
602234	WITH 2122−5, PC 19745, NP 1843−9
602235	NP 1842−8
602236	NP 1842−9
602237	NP 1842−12
602238	NP 1842−13
602242	PC 19921, 19922 PC, 2140
602243	KP 339
602250	PC 17344−1, 1744−1
602251	PC 17344−2, 1744−2
602252	PC 17344−3, 1744−3
602262	PC 18763−1, 1980−1
602263	PC 18755, 1987−1
602264	PC 18756, 1987−2
602265	PC 18763−2, 1980−2
602266	PC 18757, 1987−3
602267	PC 18763−3, 1980−3
602268	WITH 1995−1, PC 18911−1
602269	WITH 1995−2 WEEK, PC 18911−2
602270	WITH 2027−3, PC 19067−3
602271	WITH 2027−6, PC 19067−6
602272	WITH 2027−1, PC 19067−1
602273	WITH 2027−4, PC 19067−4
602274	WITH 2027−5, PC 19067−5
602275	WITH 2027−2, PC 19067−2
602276	WITH 2027−8, PC 19067−8
602277	WITH 2027−7, PC 19067−7
602380	PC 11919
602381	With 812
602382	555
602383	With 554
602384	With 786
602385	PC 11924
602386	PC-0438
602387	WITH 1332−2, PC 15221
602388	From 558
602389	With 553
602390	WITH 1332−1, PC 15228
602391	With 863−5
602392	WITH 1332−3, PC 15211
602393	With 785
602394	PC 0537
602395	PC 0437
602396	PC 11755
602397	PC 11927
602398	PC 13917
602399	PC 11926
602400	PC 11925
602401	WITH 1332−4, PC 15202
602402	PC 11928
602403	PC 11923
602404	WITH 1224, PC 14649
602405	PC 11920
602406	NP 1853−1
602407	NP 1853−2
602408	PC 4339, 2183−1, PC 7023
602409	PC 4340, 2183−2, PC 7024
602410	PC 4341, 2183−3, PC 7025
602412	KP 26
602414	NP 1853−3
602435	NP 1853−4
602701	PC 18910−1, 1994−1
602702	PC 17343, 1745
602703	PC 19066−6, 2026−6
602704	PC 19066−4, 2026−4
602705	PC 19066−2, 2026−2
602706	PC WAS 18762, 1981
602707	PC 18915, 1999
602708	PC 19066−1 WITH 2026−1
602709	PC 19066−5, 2026−5
602710	PC 19066−3, 2026−3
602711	PC 19066−7, 2026−7
602713	PC 18910−2, 1994−2
602753	PC 18917, 2001
602755	PC 18912, 1996
602756	PC 18759, 1984
602790	PP 535−1, PF 62
602791	With 1099
602792	PP 535−2, PF 63
602793	PP 535−3, PF 64
602794	PP 535−4, PF 65
602796	PC 19065−1, 2025−1
602797	PC 19065−2, 2025−2
602798	PC 19065−3, 2025−3
602799	PC 19065−4, 2025−4
602800	PC 19065−5, 2025−5
602801	PC 19065−6, 2025−6
602802	PC 19065−7, 2025−7
602803	PC 19065−8, 2025−8
602804	PC 19065−9, 2025−9
602832	PC 19068−6, 2028−6
602833	PC 19068−1, 2028−1
602834	PC 19068−2 WITH 2028−2
602835	PC 19068−5, 2028−5
602836	PC 19068−3, 2028−3
602837	PC 19068−4, 2028−4
602865	PC 4527−2
602866	PC 4527−3
602867	PC 4527−1
602868	PC 4527−5
602869	PC 4527−4
602879	PC 4876−1
602880	PC 4876−2
602881	PC 4876−3
602882	PC 4876−4
602901	PC 4528−1
602902	PC 4582−1
602903	PC 4582−2
602904	PC 4528−3
602905	PC 4528−2
602906	PC 4528−4
602907	PC 4582−3
602908	PC 18876
602909	PC 4528−5