GOST 19059-80
GOST 19059−80 replaceable cutting Inserts carbide faceted diamond shaped with an angle of 80°, with a hole and a chip breaking C-grooves on one side. The design and dimensions (with Amendments No. 1, 2, 3)
GOST 19059−80
Group 56
INTERSTATE STANDARD
CUTTING INSERTS, INDEXABLE MULTI-FACETED
CARBIDE RHOMBIC SHAPE WITH AN ANGLE OF 80°, WITH HOLE
AND A CHIP BREAKING C-GROOVES ON ONE SIDE
The design and dimensions
Rhombic throw-away (indexable) carbide cutting inserts with 80° included angle, with
cylindrical holes and chip-breaking flutes on one facе only. Design and dimensions
ISS 25.100
77.160
OKP 19 6000
Date of introduction 1982−01−01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Ministry of nonferrous metallurgy of the USSR
2. APPROVED AND put INTO EFFECT by Decision of the USSR State Committee on management of quality and standards from
3. In this standard introduced by the international standard ISO 3364−85 «Plate replaceable tungsten carbide with corner radii with a cylindrical hole. Dimensions» in terms of inserts CNMM
4. REPLACE GOST 19059−73
5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS
| The designation of the reference document referenced |
Item number |
| GOST 19042−80 |
5 |
| GOST 19086−80 |
6 |
6. The expiration time limit is removed by the Resolution of Gosstandart of the USSR from
7. EDITION with Amendments No. 1, 2, 3, approved in October 1984, April 1987, December 1990 (IUS 2−85, 8−87, 4−91)
The requirements of this standard are mandatory.
(Added, Rev. N 3).
1. (Deleted, Rev. N 3).
2. The design and dimensions of plates shall be as specified in the drawing and in the table.
__________________
* Size for reference.
mm
| The marking plates of classes of tolerances |
|||||||||||
| U |
M | ||||||||||
| digital | alphanumeric | With — me- believe it- the cost |
digital | alphanumeric | With — me- believe it- the cost |
||||||
| 05114−090304 | CNUM-090304 |
05124−090304 | CNMM-090304 | 9,7 | 9,525 | 3,81 | 3,18 | 0,4 | 2,425 | ||
| 05114−090308 | CNUM-090308 |
05124−090308 | CNMM-090308 | 0,8 | 2,205 | ||||||
| 05114−120404 | CNUM-120404 |
05124−120404 | CNMM-120404 | 12,9 | 12,700 | 5,16 | 4,76 | 0,4 | 3,307 | ||
| 05114−120408 | CNUM-120408 |
05124−120408 | СNMM-120408 | 0,8 | 3,088 | ||||||
| 05114−120412 | CNUM-120412 |
05124−120412 | CNMM-120412 | 1,2 | 2,867 | ||||||
| 05114−160412 | CNUM-160412 |
05124−160412 | CNMM-160412 | 16,1 | 15,875 | 6.35 mm | 1,2 | 3,748 | |||
| 05114−160416 | CNUM-160416 |
05124−160416 | CNMM-160416 | 1,6 | 3,528 | ||||||
| - | - |
05124−160608 | CNMM-160608 | 6.35 mm | 0,8 | 3,970 | |||||
| - |
- | 05124−160612 | CNMM-160612 | 1,2 | 3,749 | ||||||
| 05114−190608 | CNUM-190608 | 05124−190608 | CNMM-190608 | 19,3 | 19,050 | Of 7.93 | 0,8 |
4,851 | |||
| 05114−190616 | CNUM-190616 | 05124−190616 | CNMM-190616 | 1,6 |
4,411 | ||||||
| 05114−190612 | CNUM-190612 | 05124−190612 | CNMM-190612 | 1,2 |
4,631 | ||||||
| 05114−190624 | CNUM-190624 | 05124−190624 | CNMM-190624 | 2,4 |
3,960 | ||||||
Example of designation when ordering plates of hard alloy VK6 brand, class of admission U, with cutting edge length =9.7 mm, thickness
=3.18 mm radius
=0.4 mm:
19 6524
0381 090304
(Changed edition, Rev. N 2, 3).
3. The shape and dimensions of a chip breaking C-grooves are provided in Annex 1.
4. Approximate weight plates are given in Appendix 2.
5. The notation of plates according to GOST 19042.
6. Technical requirements — GOST 19086.
7. Applied alloys is given in Appendix 3.
(Added, Rev. N 3).
ANNEX 1
Recommended
The shape and dimensions of a chip breaking C-grooves on the front surfaces of the plates indicated in the drawing and in the table.
Form 1 for diameters d=9,525 12,700 mm. and Form 2 for diameters d=15,875 19,050 mm and
mm
| 9,525 |
- | 5,5 | 1,0 | 0,4 |
| 12,700 |
- | 8,0 | 0,6 | |
| 15,875 |
3,2 | - | 1,6 | - |
| 19,050 |
3,8 | - | - |
APPENDIX 1. (Changed edition, Rev. N 3).
ANNEX 2 (informative). Approximate weight plates
ANNEX 2
Reference
| Approximate weight of plates, g | |||||||||
| Digital signage plates | carbide grades | of tungsten carbide |
hard alloy coated | ||||||
| VK6 | VK8 |
Т5К10 | Т14К8 | T15K6 | КНТ16, ТН20 | ВП1255 | ВП3115 | ВП3325 | |
| 05114−090304 |
3,56 | Of 3.51 | Is 3.08 | 2,79 | Of 2.74 | 1,39 | 3,26 | 3,56 | Of 3.51 |
| 05124−090304 | |||||||||
| 05114−090308 |
3,54 | 3,49 | 3,06 | 2,77 | 2,73 | 1,38 | 3,24 | 3,54 | 3,49 |
| 05124−090308 |
|||||||||
| 05114−120404 |
9,43 | Of 9.31 | 8,16 | 7,39 | 7,27 | 3,68 | 8,65 | 9,43 | Of 9.31 |
| 05124−120404 |
|||||||||
| 05114−120408 |
9,40 | 9,28 | 8,13 | Of 7.37 | 7,24 | 3,67 | 8,63 | 9,40 | 9,28 |
| 05124−120408 |
|||||||||
| 05114−120412 |
9,36 | Of 9.23 | 8,09 | 7,33 | 7,21 | 3,65 | 8,60 | 9,36 | Of 9.23 |
| 05124−120412 |
|||||||||
| 05114−150412* |
14,70 | 14,50 | 12,70 | 11,50 | 11,40 | 5,73 | Of 13.48 | 14,70 | 14,50 |
| 05124−160412 |
|||||||||
| 05114−160416 |
14,70 | 14,50 | 12,70 | 11,50 | 11,30 | 5,73 | Of 13.48 | 14,70 | 14,50 |
| 05124−160416 |
|||||||||
| 05114−190608 |
28,10 | 27,70 | 24,30 | 22,00 | 21,60 | - | Of 25.76 | 28,10 | 27,70 |
| 05124−190608 |
|||||||||
| 05114−190612 |
28,00 | 27,60 | 24,20 | 22,00 | 21,60 | - | 25,66 | 28,00 | 27,60 |
| 05124−190612 |
|||||||||
| 05114−190616 |
27,90 | Of 27.30 | 24,20 | 21,90 | 21,50 | - | 25,57 | 27,90 | 27,50 |
| 05124−190616 |
|||||||||
| 05114−190624 |
27,70 | Of 27.30 | Of 23.90 | Of 21.70 | 21,30 | - | Of 25.39 | 27,70 | Of 27.30 |
| 05124−190624 | |||||||||
________________
* Consistent with the original. — Note the manufacturer’s database.
APPENDIX 2. (Changed edition, Rev. N 2).
APPENDIX 3 (recommended). Applied grades of plates
APPENDIX 3
Recommended
| Digital signage plates |
The main application | The additional use of | Application by special order |
| 05114−090304 |
N 4 | N 9 | N 3, N 5, N 6, N 7, N 8, N 10, 11 |
| 05124−090304 | - | - | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 |
| 05114−090308 |
N 4, N 7 | N 9 | N 3, N 5, N 6, N 8, N 10, N 11 |
| 05124−090308 | - | - | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 |
| 05114−120404 |
N 4, N 7 | N 9 | N 3, N 5, N 6, N 8, N 10, N 11 |
| 05124−120404 | N 7 | - | N 3, N 4, N 5, N 6, N 8, N 9, N 10, N 11 |
| 05114−120408 |
N 4, N 5, N 7 | N 9, N 11 | N 3, N 6, N 8, N 10 |
| 05124−120408 | N 3, N 5, N 6, N 7 |
N 9 | N 4, N 8, N 10, N 11 |
| 05114−120412 |
N 4, N 5, N 7 | N 11 | N 3, N 6, N 8, N 9, N 10 |
| 05124−120412 | - | - | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 |
| 05114−160412 |
N 4, N 5, N 7 | N 9, N 11 | N 3, N 6, N 8 |
| 05124−160412 |
N 3 | N 9 | N 4, N 5, N 6, N 7, N 8, N 10, N 11 |
| 05114−160416 | - | - | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 |
| 05124−160608 | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 | ||
| 05124−160612 | |||
| 05114−190608 | N 7 | N 3, N 4, N 5, N 6, N 9, N 10, N 11 | |
| 05124−190608 |
N 3, N 10 | - | N 4, N 5, N 6, N 7, N 9, N 10 |
| 05114−190612 | N 4, N 5, N 7 |
N 10 | N 3, N 6, N 9, N 11 |
| 05124−190612 | N 3, N 7 |
N 10 | N 3, N 4, N 5, N 6, N 11 |
| 05114−190616 | N 4, N 5, N 7 |
N 10 | N 3, N 6, N 9, N 11 |
| 05124−190616 | N 7 |
N 10 | N 3, N 4, N 5, N 6, N 11 |
| 05114−190624 |
- | - | N 3, N 4, N 5, N 6, N 7, N 9, N 10, N 11 |
| 05124−190624 | |||
| 05124−160416 | N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10, N 11 |
N 3 — VK6; N 4 — VK8; N 5 — Т5К10; N 6 — Т14К8; N 7 — T15K6; N 8 — КНТ16, ТН20; N 9 — ВП3115; N 10 — ВП3325; N 11 — ВП3115.
ANNEX 4 (reference). The applicability of the plates
ANNEX 4
Reference
| Marking | Plate with a chip breaking C-grooves on one side | |||||
The radius | ||||||
| 0,4 | 0,8 |
1,2 | 1,6 | 2,4 | ||
| 12,7 | CNMM 1204 |
++ | + | + | ++ | +++ |
| 15,875 | CNMM 1606 |
+++ | + | + | ++ | +++ |
| 19,05 | CNMM 1906 |
+++ | ++ | + | + | +++ |
| 25,4 | CNMM 2509 |
+++ | +++ | +++ | +++ | ++ |
Note. + — plates of the basic application, standardized.
++ — plates have limited use, not standardized.
+++ — plates are not recommended for use.
APPS 3, 4. (Added, Rev. N 3).
