By visiting this site, you accept the use of cookies. More about our cookie policy.
Will call in 30 seconds. Free.

Copper rod, wire, tube, sheet, strip made of C11000 - 2.0090

Buy C11000 — 2.0090 at a bargain price

«Auremo» C11000 — 2.0090 supplier offers to buy copper mill-products. They comply with GOST and International Standards of quality. A wide selection of products, comprehensive consulting service, affordable C11000 — 2.0090 price and short-time delivery define a company’s image. C11000 — 2.0090 rod, wire, pipe, strip are always in stock.

Copper C11000 — 2.0090 characteristics

C11000 is a high-quality copper with a high content of main metal in composition. Plumb, arsenic, nickel, iron, sulfur, antimony, tin, bismuth are also presented in composition. C11000 grade has high electric and heat conductivity, plasticity, corrosive resistance, and processability. Grade C11000 is used in manufacturing of requested alloys of non-iron metals such as bronze and brass. Alloying components (phosphorus, nickel etc.) in composition influence on copper characteristics. Depending on manufacturing method, there are distinguished the different copper grades: By physical parameters, copper can be: soft or hard.


Copper is the most widespread non-iron material. It differs with high anticorrosive properties not only in fresh or sea water but in different aggressive environments as well. Despite this, copper is non-resistant in environment of ammonia and sulfur dioxide. It can be easily brazed and pressure treated. Possessing limited casting properties, copper is hardly welded and cut. Usually, it is used in a form of pipes, busbars, sheets, bars, wire. Oxygen content in C11000 constitutes about 0.05−0.08%.

Industrial application: smelt of high-quality bronze, brass; manufacture of current-carrying conductors, parts of cryogenic equipment, bars and wires for automatic welding under flux or in environment of cast iron or copper.

Percentage composition

Element Content
Pb <0,005
Ag <0,003
Zn <0,004
Fe <0,005
S <0,004
As <0,002
Cu 99.9
Ni <0,002
Fe <0,005
S <0,004
As <0,002
Cu 99.9

Main properties

Casting temperature: 1150 — 1250°C

Point of melting 1083°C

Alloy hardness: HB 10 -1 = 45 MPа

Linear shrinkage: 2,1%

Coefficient of friction with lubricant = 0.011

Coefficient of friction without lubricant = 0.46

Mechanical characteristics at a temperature of 20 °C.

Mill-products δ5 (%)

KCU kJ/m2

ψ % sT (MPa) TS (MPa)
hard alloy 6     300−450 400−490
soft alloy 60     90−150 200−250

YS — permanent change of form — yield strength (proportionality), MPa

TS — ultimate tensile strength (rupture strength), MPa

Physical properties of C11000 grade

R 10 9(Ohmm)

C (J/(kg/degree))

r (kg/m3)

l (V/(mDegree))

a 10 -6 (1/Degree)

E 10— 5 (MPa)

t° (degree)
17,8 390 8940 387   1,28 20°
        16,7 1,32 100°

Casting and technological properties of C11000 grade

Description Identification
Casting temperature: 1150 — 1250°C
Linear shrinkage: 2,1%
Point of melting 1083°C

Foreign analogs of C11000

France Italy the USA Japan Germany England EU









C106 Cu-ETP
Description Identification Description Identification
— differential deposit at a process of first crack appearing, % å — heating capacity of alloy (heat conduction coefficient), V/(m°С) l
— maximum shear stress, ultimate torsional strength, MPa — elastic strength, MPa σ0,05
— ultimate bending strength, MPa σ bend — conventional yield limit, MPa σ0,2
— fatigue endurance limit during bending test with symmetrical load cycle, MPa σ-1 — percentage elongation after rupture, % δ5,δ4,δ10
— fatigue endurance limit during torsion test with symmetrical load cycle, MPa J-1 — yield stress (contraction), MPa YS 0,05
— amount of load cycling n — relative shear, % v
— specific electrical resistance, Ohm-m R and ρ — short ultimate tensile strength, MPa TS
— standard module of elasticity HPa E — contraction ratio, % ψ
— properties getting temperature, Degree T — impact hardness, which is established on specimens with concentrators in accordance with V and U types, J/cm2 KCU and KCV
— specific heat of alloy (temperature range is 20°С), [J/(kg-deg)] C — Brinell hardness HB
— density, kg/m3 pn and r — Vicker’s hardness HV
— linear thermal expansion coefficient (in a temperature range of 20°С), 1/°С a — Rockwell hardness C HRC
— long-time strength limit, MPa σtТ — Rockwell hardness B HRB
— module of elasticity at a process of torsional shear, HPa G — Shore hardness HSD

C11000 — 2.0090 supplier

«Auremo» supplier offers to buy C11000 — 2.0090 by wholesale. A wide range of goods is presented in stock. They comply with GOST and International Standards of quality. Copper rod, wire, tube are always in stock. You can buy them for the best C11000 — 2.0090 price from C11000 — 2.0090 supplier. Buy C11000 — 2.0090 right now! C11000 — 2.0090 price is privileged for wholesale buyers.

Our consultant will save your time

+7 (962) 383-76-36


Special offers and discounts. :)